You’ve found a temperature and humidity sensor with the right measuring range and accuracy. But then you face three output options: 4–20mA, 0–10V, and RS485.
Which one should you choose?
Choosing the wrong output can mean your sensor won’t communicate with your PLC, HVAC controller, or monitoring system without additional equipment.
The good news? You don’t need to be an electrical engineer to understand the differences.
Here’s the quick answer:
- 0–10V: A practical option when your existing HVAC or building controller accepts analog voltage inputs.
- 4–20mA: Often preferred for industrial environments, particularly where cables run over longer distances or electrical interference is a concern.
- RS485: Useful for digital communication and systems with multiple monitoring points, provided the devices support compatible communication protocols.
The best choice isn’t necessarily the newest or most advanced option. It’s the one that fits your existing system and project requirements.
Let’s make the differences easy to understand.
1. What Is the Difference Between 4–20mA, 0–10V, and RS485?
Think of these three outputs as different ways a sensor tells your control system what it’s measuring.
0–10V: Like a Light Dimmer
Imagine a light dimmer. As you turn the knob, the brightness changes.
A 0–10V humidity sensor works in a similar way. Instead of controlling brightness, it changes its output voltage to represent humidity.
For example, if a sensor is configured for a 0–100% relative humidity (RH) range:
- 0V represents 0% RH.
- 5V represents 50% RH.
- 10V represents 100% RH.
Your controller reads the voltage and converts it into a humidity value.
When does this make sense?
When your HVAC or building automation controller already has compatible 0–10V analog inputs.
It’s a straightforward solution, but voltage signals require attention to cable length, grounding, and electrical interference.
4–20mA: Like Measuring Water Flow
Imagine measuring water flowing through a pipe. The flow rate changes to represent different measurements.
A 4–20mA sensor uses electrical current in a comparable way.
For a hypothetical 0–100% RH range:
- 4mA represents 0% RH.
- 12mA represents 50% RH.
- 20mA represents 100% RH.
Why start at 4mA instead of zero?
Because 4mA provides a live zero. A current near 0mA can indicate a broken circuit, lost power, or another fault rather than a normal minimum reading.
Current-loop signals are also generally less sensitive to voltage drops along the cable.
When does this make sense?
When connecting sensors to compatible industrial PLCs or data acquisition systems, especially where long wiring routes or electrical noise are concerns.
RS485: Like a Wired Group Conversation
Imagine several people communicating through one organized group conversation.
Instead of every person needing a separate connection to the listener, they share a communication channel.
RS485 provides a physical interface for digital communication. With the appropriate protocol, several sensors can share a communication bus, and a controller can identify which device is providing information.
Unlike a single analog signal, a compatible digital system can communicate multiple measurements, including temperature and humidity, through one interface.
However, there’s an important detail:
RS485 is not the same thing as Modbus RTU.
RS485 defines the electrical communication interface. Modbus RTU is one protocol that can operate over RS485.
Two devices with RS485 ports aren’t automatically compatible.
When does this make sense?
When your system supports the sensor’s communication protocol and you need digital readings, centralized data collection, or multiple monitoring points.
2. 4–20mA vs 0–10V vs RS485: Quick Comparison
Here’s a practical comparison for industrial temperature and humidity monitoring.
| Feature | 0–10V | 4–20mA | RS485 |
|---|---|---|---|
| Signal type | Analog voltage | Analog current | Digital communication |
| Typical controller | HVAC/DDC, PLC voltage input | PLC/DCS current input | PLC, gateway, compatible digital controller |
| Cable distance | Generally better for shorter runs | Often better for longer runs | Can support long bus runs with proper design |
| Noise resistance | More sensitive to interference | Generally strong | Good when correctly installed |
| Multiple sensors | Separate input channels | Separate input channels | Multiple compatible devices can share a bus |
| Setup complexity | Usually simple | Usually simple to moderate | Requires communication configuration |
| Main consideration | Voltage input compatibility | Current input and loop requirements | Protocol and serial compatibility |
| Common application | Building automation | Industrial monitoring | Multi-point monitoring systems |
These are general engineering characteristics, not guaranteed specifications for every sensor. Actual performance depends on the device, cable, controller, and installation.
The most important takeaway: Start by checking what your receiving equipment can accept.
A 4–20mA transmitter isn’t a direct replacement for a 0–10V transmitter, and an RS485 port doesn’t automatically support every digital sensor.
3. Which Output Is Better for Distance, Noise, and PLC Compatibility?
Three practical questions can help you eliminate unsuitable options.
How Far Can the Signal Travel?
Imagine placing a humidity sensor in an HVAC duct while the control cabinet is located elsewhere in the building.
The longer the cable, the more important the signal characteristics become.
0–10V: Voltage readings may be affected by wiring resistance, ground potential differences, and electrical noise. Short, well-designed connections are often easier to manage.
4–20mA: Current-loop systems can often transmit measurements over longer cable routes without the same sensitivity to voltage drops at the receiving input. However, loop resistance and available supply voltage still matter.
RS485: Differential digital signaling can support long communication buses, but cable length depends on data rate, cable characteristics, termination, and network design.
There is no single maximum distance that applies to every product.
Practical tip: Before ordering, check the approximate distance between your sensor and controller. Don’t choose an output solely because a general guide mentions a particular distance.
What About Electrical Interference?
Factories often contain motors, variable-frequency drives, and power cables that can interfere with measurement signals.
4–20mA is frequently chosen for these environments because current-loop measurement is relatively resistant to common wiring-related disturbances.
RS485 also provides good noise resistance through differential signaling when installed correctly.
0–10V can work reliably too, particularly with appropriate cable routing and a stable signal reference.
The right answer depends on the installation, not simply the signal name.
Will It Work With Your PLC?
This is often more important than distance.
Check your controller’s input specifications:
| Your Equipment Has | Output to Consider |
|---|---|
| 0–10V analog voltage input | 0–10V transmitter |
| 4–20mA analog current input | 4–20mA transmitter |
| RS485 interface with compatible protocol | RS485 transmitter |
| Only Ethernet or another incompatible interface | An appropriate gateway or different transmitter may be required |
For temperature and humidity measurement, remember that many analog transmitters provide two separate outputs.
You may need two available analog input channels—one for temperature and one for humidity.
A compatible RS485 transmitter can communicate both measurements through one digital interface, although the receiving system must know how to interpret the data.
4. Which Output Should You Choose for Your Application?
Let’s look at three realistic project situations.
Scenario 1: HVAC Duct Monitoring in a Commercial Building
You’re installing a temperature and humidity sensor in a ventilation duct.
Your existing HVAC controller has available 0–10V inputs, and the wiring route is relatively short.
Recommended starting point: 0–10V.
There’s little reason to introduce an RS485 gateway when your existing controller already supports the required analog inputs.
Just confirm the number of channels, supply voltage, and measurement scaling.
Scenario 2: Industrial Air Monitoring Near Production Equipment
You need to measure air temperature and humidity in a factory ventilation system.
The sensor is relatively far from the control cabinet, and the installation includes electrical equipment that may generate interference.
Your PLC already has 4–20mA analog input channels.
Recommended starting point: 4–20mA.
It’s a practical option for this type of industrial installation, provided the transmitter, power supply, input module, and cable design are compatible.
Scenario 3: Multiple Sensors Connected to a Central Monitoring System
You’re designing a facility monitoring system with several temperature and humidity measurement locations.
Your controller or gateway supports an appropriate RS485 communication protocol.
Recommended starting point: RS485.
A digital bus may simplify system expansion and allow multiple compatible transmitters to communicate through shared wiring.
However, you must verify device addresses, protocol settings, bus topology, and communication documentation before installation.
These are selection examples, not completed project case studies. Actual product suitability must be checked against the installation requirements.
5. How to Choose the Right Temperature and Humidity Sensor Output
Before requesting a quotation, run through these six checks.
1. Check your controller’s input type.
Does it accept 0–10V, 4–20mA, or RS485? If RS485, which communication protocol does it support?
2. Confirm the measurements you need.
Do you need humidity only, or both temperature and humidity? Check whether sufficient analog input channels are available.
3. Estimate the cable distance.
Know roughly how far the sensor will be from the receiving equipment and whether the cable passes through electrically noisy areas.
4. Check the installation location.
Will the probe be mounted inside an air duct or another air-measurement location? Consider insertion depth, mounting space, airflow, and environmental exposure.
5. Verify the power supply.
Don’t assume transmitters with different output signals—or even different product housings—have identical power requirements.
6. Consider future expansion.
If you’re adding many measurement points, compare the total costs of analog input modules, wiring, gateways, and digital network configuration.
Buying tip: A less expensive sensor isn’t necessarily the less expensive system. Include compatibility, installation, commissioning, and maintenance in your decision.
6. Compare Orivelor Temperature and Humidity Transmitters
Orivelor offers six FG-series temperature and humidity transmitters covering the three output options.
All six are intended for air temperature and relative humidity measurement, with flange-mounted probe configurations.
| Required Output | Compact FG60 Series | FG70 Series with Junction Box |
|---|---|---|
| 0–10V | FG6010 | FG7010 |
| 4–20mA | FG6020 | FG7020 |
| RS485 | FG6485 | FG7485 |
FG60 vs FG70: What’s the Difference?
The FG60 series uses a compact probe-style design with an attached cable.
The FG70 series adds an aluminum junction box for access to wiring connections.
For example, FG6020 and FG7020 both provide separate 4–20mA signals for temperature and humidity, but they have different electrical supply requirements:
- FG6020: 12–36V DC
- FG7020: 15–24V DC
This is why selecting the output signal is only the first step. You should also compare installation dimensions, wiring arrangements, power requirements, and measurement specifications.
For RS485 models, FG6485 and FG7485 communicate temperature and humidity readings digitally. Confirm the communication protocol and settings before connecting either model to your controller.
Explore the complete Orivelor product range to compare the available configurations.
7. Frequently Asked Questions
Is 4–20mA better than RS485 for industrial humidity monitoring?
Neither is universally better. 4–20mA is often simpler when your existing PLC has current inputs and you only need a few measurement points. RS485 can be more useful for multiple devices or digital data collection, provided the communication protocol is compatible.
Is RS485 the same as Modbus RTU?
No. RS485 is an electrical interface, while Modbus RTU is a communication protocol. A device with RS485 does not necessarily support Modbus RTU. Always confirm the actual protocol and communication documentation.
Can I connect a 4–20mA sensor to a 0–10V PLC input?
Not directly as interchangeable signal types. You need a suitable current input, a compatible conversion arrangement, or another properly engineered interface. Check the PLC input specifications before selecting a converter.
Why does a 4–20mA signal start at 4mA?
The 4mA starting point represents the minimum measurement while maintaining a live signal. This helps distinguish normal minimum readings from conditions such as an open circuit or loss of power, although exact fault detection depends on the system.
Can multiple humidity sensors share one RS485 cable?
Yes, when the devices and communication protocol support a shared bus. Each device generally needs a distinct address, and wiring, termination, baud rate, and other communication settings must be configured correctly.
How do I convert 4–20mA or 0–10V into humidity percentage?
Your controller scales the electrical signal to the transmitter’s configured humidity range.
For an illustrative 0–100% RH range, 12mA from a 4–20mA transmitter or 5V from a 0–10V transmitter represents 50% RH.
Always use the actual measurement range specified for your transmitter rather than assuming every product is scaled identically.
8. Final Recommendation: Match the Sensor to Your System
When comparing 4–20mA vs 0–10V vs RS485, don’t start by asking which technology is best.
Start with three questions:
- What input or communication interface does my controller support?
- How many sensors and measurements does my project require?
- What are the wiring distance and installation conditions?
If you’re integrating a sensor into an existing HVAC controller with voltage inputs, 0–10V may be the simplest option.
If you have industrial current inputs and longer cable runs, 4–20mA may be a better starting point.
If you’re building a multi-point digital monitoring network, RS485 is worth considering—as long as the devices can communicate using compatible protocols.
Need Help Choosing a Compatible Temperature and Humidity Transmitter?
Orivelor helps B2B buyers and system integrators identify suitable temperature and humidity monitoring products.
You don’t need to know every technical specification before contacting us.
Send us your PLC or controller model, preferred output signal, installation conditions, estimated quantity, and destination country.
We’ll help you review the available FG-series options and identify which product specifications need to be confirmed for your project.
Contact Orivelor for Product Selection & Quotation
Still deciding between an industrial sensor and a digital display? Read our guide: Temperature and Humidity Sensor vs. Meter: What’s the Difference?
